Provides information to enable POS operators to use the TM-. L90 safely and correctly. TM-L90 Service Manual. Describes maintenance, inspection and repair . EPSON has been taking industryinitiatives with its own POS printer . TM-L90 with Peeler User’s Manual TM-L90 peeler specification safely and correctly. Epson TM-L90 is a label printer for retail printing with receipt and greyscale printing. It also has greyscale for multi-tone printing.

Author: Grogor Vujind
Country: Cape Verde
Language: English (Spanish)
Genre: Sex
Published (Last): 1 February 2011
Pages: 131
PDF File Size: 16.87 Mb
ePub File Size: 5.2 Mb
ISBN: 493-8-68332-362-3
Downloads: 57731
Price: Free* [*Free Regsitration Required]
Uploader: Meztir

When mounting or replacing the paper roll, be careful not to touch the manual cutter, because it is sharp and can injure you. Remove one manual cutter screw 4. You can easily print on different types of label and receipt tn-l90, in a variety of different sizes, thanks to the adjustable cutter.

Remove two W1 washers and one motor manuaal plate by removing three N1 nuts. Confidential Electrical Specifications Operating voltage: Confidential Cover Unit The cover unit is installed onto the paper supply unit by a hinge, and it makes a rotational movement. After you have installed the paper holding rollers, lubricate with G at the 16 points shown below. Confidential Main Case Assembly 1.

Quick Links

While holding the two head holder springs so they do not fly out, pull out the spring holder plate. B viii Add the information of the related documentation Reason for change: Secure the autocutter unit with the two S4 screws. Remove one S4 screw 2. Mt-l90 down your equipment immediately if it produces smoke, a strange odor, or unusual noise.


Vertical installation Horizontal installation 5. When installing it, make sure the claw has been hooked. This printer benefits from high speed serial, Ethernet and parallel connectivity plus a built-in USB interface, which means it can be operated as a network device. Buttons and Switches Power switch The power switch non-locking, push switch on the right part of the front face of the unit turns the epsin on or off.

Attach the autocutter unit in its installation position. Lubricate the contact area of frame R and the front frame with G This allows the TM-L90 to receive paper roll in the correct position, whether the unit is installed vertically or horizontally.

Install a paper roll. Page 11 Do not block the label peeler detector with your fingers, or anything else while the label issuing is in progress.

Remove the insulating tape that is securing the lead wire of the BM black mark paper detector circuit board assembly. Remove one S4 screw. Page Confidential Paper Specifications Specified roll paper: Page 5 Neither is any liability assumed for damages resulting from the use of the information contained herein. So the following illustration is changed. Register now We respect your privacy.

Cut the plastic sheet with a cutting tool such as a cutter knife. Your email address or other details will never be shared with any 3rd parties and you will receive only the type of content for which you signed up.

Read the following carefully before handling the product. This process is necessary only if the original NE detector lead wire has insulation tape affixed. Page 13 You can clean them easily if you use a wasted label, as shown in the illustration. Such solvents may enter the roller shaft and cause a malfunction of the peeler. Page 39 Confidential 5.


Epson TM-L90 series Service Manual

Troubleshooting Chapter 2 Troubleshooting Guide C Parts List Appendix D Don’t have an account? Using Different Paper Widths Be sure spson set the paper width with the memory switch to match printing to the print width. The following original paper types can be used. Remove frame strengthening plate L. Confidential Reduction Gears 1.

Mounts horizontally, vertically or with a wall bracket Easy operation: Continued use may lead to fire or electric shock.

Epson TM-L90 Series – Epson

Only disassemble this product as described in this manual. Install in the reverse sequence of removal. The manual cutter has a sharp blade.

Table of Contents Add to my manuals Add. Page 75 Confidential Note: Remove one E2 type E retaining ring, and slide the lever shaft to remove the lever button. Find a dealer Location. When installing the fixed blade, see the drawing below to check the installation direction. The label guide is attached to the label holder and interlocks with the cover unit.