ALLEN BRADLEY 1305 VFD MANUAL PDF

However, using an Allen-Bradley motor with your drive removes the . Н Installation guidelines called out in Appendix D of the User’s Manual. Installation Instructions IN. May, Allen-Bradley. Dynamic Brake. Cat. No. KAA KBA03, KBA06, KBA Table of Contents. Find great deals for Allen Bradley Adjustable Frequency AC Drive User Manual. Shop with confidence on eBay!.

Author: Kigara Akinorg
Country: South Sudan
Language: English (Spanish)
Genre: Art
Published (Last): 24 March 2012
Pages: 263
PDF File Size: 18.44 Mb
ePub File Size: 4.48 Mb
ISBN: 703-9-74021-776-2
Downloads: 13234
Price: Free* [*Free Regsitration Required]
Uploader: Zolot

Inspect for breaks in communications line. Inspect for short at the drive output or excessive load conditions on the motor, especially cable capacitance to ground. Stop drive, then re-run download. Capabilities of drive are different than the master drive. Error 3 – Download was attempted to a different type drive i. Check the motor for grounded phase.

Inspect the wiring between the drive and motor. Unplug the HIM from the cable or drive and reconnect it. Power Test Fault – F46 Fault detected during initial start-up sequence. Overload Fault – F7 Internal electronic overload trip. Unplug the HIM from the cable or drive, then reconnect it. Check the motor and external wiring to the drive output terminals for a shorted condition.

Reset your drive to the factory default settings. Check for a short circuit at the drive output or excessive load conditions at the motor. Error 2 – The number of parameters in saved profile does not equal master number. Verify that all parameters have been programmed. Motor Stall Fault vff F6 The motor has stalled If the motor is drawing excessive current, the motor load is bradoey and will not allow the drive to accelerate to set speed. If not, manually program any remaining parameters.

  LIBRO DE NUTRIOLOGIA MEDICA ESTHER CASANUEVA PDF

Allen Bradley 1305 Adjustable Frequency AC Drive User Manual

The Adjustable Frequency AC Drive is a variable speed drive designed to control the speed of three-phase AC induction motors in a variety of demanding applications where flexibility, performance and ease of use are essential. Fast repairs at low costs.

The last parameter programmed will be displayed on the top line. Change [Cable Length] to “Long” if applicable. Overcurrent Fault – F12 Overcurrent is detected in overcurrent hardware trip circuit.

Extend the deceleration time or instal dynamic brake option. Overspeed Fault – F25 Internal error. Hz Sel Fault – F30 An unconnected adapter has mznual selected as the active frequency source.

Reduce [Start Boost] if applicable. Check for broken wires, loose connections, or transducer loss at mA input, TB2. Reprogram Fault – F48 May occur when drive parametersare reset to default settings.

Allen Bradley Adjustable Frequency AC Drive User Manual | eBay

Verify that the parameter has been programmed correctly. Save a new profile. Check programming of [Curr Lim Trip En] parameter. An external pot is connected and the ground lead of the pot is disconnected, creating brqdley potential drive overspeed hazard. If the motor is drawing excessive current, the motor load is excessive and will not allow the drive to accelerate to set speed.

Allen Bradley Adjustable Frequency AC Drive AB

DC Braking cannot be used with a synchronous motor. Inspect for blocked or contaminated aleln sink fins. Error 4 – Saved data for parameter not correct for new drive.

  JACOB AAGAARD GRANDMASTER PREPARATION PDF

An attempt has been made to set the [Run Boost] parameter to a value greater than the [Start Boost] parameter. An active local bus adapter is disconnected while it possesses control of a local bus function. Check for excess load, manuxl DC boost setting, DC brake volts set too high or other causes of excess current. Check for proper mounting and spacing. Phase V Fault – F39 A phase to ground fault has been detected between the drive and motor in this phase.

Hz Err Fault – F29 No valid operating frequency. Serial Fault – F10 An active local bus adapter is disconnected while it possesses control of a local bus mznual. Replace the Communication cable. Check the external potentiometer circuit at TB2, terminals 1, 2, and 3 for a disconnected current. Correct the cause of the fault and manually clear by cycling the stop command or cycling power. No valid operating frequency. Inspect to ensure that the ambient temperature limit has not been exceeded.

The Adjustable Frequency AC drive is available with ratings 0. Check cable connection from main control board to power board. Drive Reset Fault – F22 May occur on power-up. A longer acceleration tiime or a lighter load may be required. May occur on power-up.

Check motor for grounded phase.